16mm Press Fitting Wall Elbow with 1/2" Female Thread

Yes, this press fitting is DVGW-certified for multilayer composite pipes and is also suitable for copper pipes.

Yes, the wall bracket is fully suitable for drinking water. It is DVGW-certified and complies with the UBA positive list.

Yes, the wall bracket is suitable for drinking water and heating installations. The maximum load is 10 bar and 70°C for 50 years.

The wall angle is flow-optimized and has a free passage. This results in virtually no flow noise.

Yes, all components are low in lead or lead-free, DVGW-certified, and comply with the UBA positive list. They fully meet the requirements of the drinking water ordinance.

The press fitting is DVGW-certified for multi-layer composite and copper pipes. For compliance with regulations, however, system-approved pipes should be used.

A compliant and safety-tested connection is only possible when using system-approved components. Using pipes from other manufacturers than Boni-Shop is at your own risk.

For the 16 x 2.0 mm press fitting, you need press jaws with TH or U contour. The angle is fully Multikontur (TH + U) compatible.

The wall bracket is designed for long-term durability of 50 years at 10 bar and 70°C. It meets the requirements of the drinking water ordinance in the long term.

The correct insertion depth of the tube is recognized by the three inspection windows in the stainless steel press sleeve. These indicate whether the tube has been inserted to the stop.

Yes, the integrated plastic guide ring ensures precise and safe pressing, even in tight situations. This minimizes the risk of a faulty connection.

The maximum operating temperature of the wall bracket is 95°C. The long-term durability is at 70°C.

For assembly, you will need a pipe cutter, a calibrator, and a suitable crimping tool with TH or U crimp profile.

Yes, the angle is "unpressed and leaky". This means an incorrectly pressed connection will let water escape immediately during a pressure test or startup. The integrated inspection window in the stainless steel sleeve also helps check the correct insertion depth of the pipe.

Yes, the angle fitting is fully suitable for drinking water pipelines and meets the requirements of the drinking water ordinance. All components are DVGW-certified and have low lead content or are lead-free.

Yes, the wall bracket is fully suitable for drinking water installations and is DVGW-certified. It also complies with the UBA positive list.

A compliant connection is only guaranteed with system-approved components where fittings and pipes have been tested together. The use of composite pipes other than those sold by Boni-Shop is at your own risk.

The pressfitting is designed for a continuous pressure resistance of 10 bar. This ensures reliable performance even at common higher water pressures.

No, the risk is minimized by the system. The guide ring ensures precise positioning, and the void-free compression with two O-rings prevents the ingress of oxygen from the air.

The press fitting 20x2 is multi-contour and fully compatible with TH and U press jaws. You need a suitable press tool with one of these press contours.

Yes, the BONI-P62WWM2004 features a special plastic guide ring. It prevents the pipe from being pushed out before the actual pressing process and ensures a precise position in the press jaw. The result is a secure and void-free connection.

Yes, due to the void-free compression and the two O-rings, the ingress of air oxygen is prevented. The system offers the highest safety here.

The plastic guide ring allows secure compaction even in tight spaces. The correct insertion depth of the pipe is easily recognizable through the integrated inspection windows in the stainless steel sleeve.

Yes, the press fitting is designed for a maximum operating temperature of 95°C. It provides a continuous load capacity of 10 bar at 70°C for 50 years.

Yes, this angle is fully compatible with the 20 x 2.0 mm dimension with both TH and U crimping jaws. You can use your crimping tool with a U-profile for this.

No, the wall elbow has a new modern contour and is flow-optimized. It provides a free passage and virtually no flow noise, supported by the best ZETA values.

Yes, the press fitting is designed for a continuous load of 10 bar at 70° C for over 50 years. This information applies to continuous operation under appropriate conditions.

The wall angle is a fitting system for two pipe systems: Multi-layer composite and copper pipes are both DVGW-certified and compatible. For a compliant connection, use system-approved components.

Yes, the wall bracket is designed for continuous use up to 70°C. The maximum operating temperature is even 95°C.

The fitting is DVGW and KIWA certified and fully suitable for drinking water. It complies with the UBA positive list, is low in lead or lead-free, and meets the requirements of the Drinking Water Ordinance.