16mm Press Fitting Coupling - Reliable Pipe Connector, Made in Germany

Yes, the BONI-P62UA1605 coupling is fully compatible with TH and U-press jaws. You can use both contours for a secure press.

The two O-rings are part of the void-free compression. They effectively prevent the ingress of atmospheric oxygen into the system and increase the safety of the connection.

The 'Made in Germany' label stands for high quality standards and precise manufacturing. A separate extended warranty is not offered, but the product features ensure durability for 50 years.

This press fitting was designed as a system for two pipe systems. It is DVGW-certified for multilayer composite and copper pipes and is equally suitable for both.

The coupling is durable up to 70° C at 10 bar pressure for over 50 years. The maximum operating temperature is even 95° C.

Yes, the coupling is permanently loadable up to 70° C at 10 bar for 50 years. The maximum operating temperature is 95° C.

Yes, the press fitting is suitable for hot water pipes with an operating temperature of up to 95°C. Long-term durability is guaranteed at 70°C for 50 years, and for short-term peaks up to 95°C, safety is maintained.

Yes, the coupling is fully suitable for drinking water. All components are DVGW-certified and lead-free, ensuring long-term safety.

No, the integrated guide ring prevents the pipe from being pushed out before the pressing process. This ensures a secure connection.

Yes, after cutting the pipe, the end must be calibrated and deburred with a calibrator. This is necessary for a safe and standards-compliant connection.

Yes, the black plastic guide ring allows safe compression even in tight or difficult conditions (constrained positions).

The coupling is technically compatible with other composite pipes. However, a regulation-compliant and system-tested connection exists only when using Boni-Shop composite pipes or system-approved components.

Yes, this coupling in the dimension 16 x 2.0 mm is Multikontur-compatible. It can be safely pressed with both TH and U-jaws.

No, the modern contour of the fitting is optimized for flow and ensures a free passage. This results in virtually no flow noises.

Yes, the Pressfitting coupling is unpressed and leaky. Proper pressing is mandatory to ensure the connection's tightness.

The multicontour compatibility (TH + U) applies to press fittings up to the dimension 32 x 3.0 mm. Larger dimensions such as 40, 50, or 63 mm must be pressed exclusively with TH press jaws.

The void-free compression and the two O-rings are designed to permanently prevent the penetration of air oxygen. This significantly contributes to the system's longevity beyond the stated continuous load capacity of 50 years.

Yes, the plastic guide ring ensures a secure fit. Additionally, the integrated inspection window in the stainless steel sleeve helps check the correct insertion depth.

Yes, with the illustrated installation guide and the right tools (pipe cutter, calibrator, press tool) the installation is also well manageable for DIY enthusiasts. It is important to use system-approved components.

Yes, this fitting system is suitable for both pipe systems: both for multilayer composite and copper pipes, provided they are DVGW-certified.

Yes, the fitting is low-lead or lead-free. All components are DVGW-certified, comply with the UBA positive list, and meet the requirements of the Drinking Water Ordinance.

The plastic guide ring ensures secure pressing even in tight positions. The integrated inspection window in the stainless steel sleeve helps you check the correct insertion depth of the pipe.

No, thanks to the flow-optimized contour and free passage, there is practically no flow noise to be expected. The best ZETA values also ensure the maximum possible passage area and thus minimal pressure loss.

The fitting is flow-optimized and has a free passage, ensuring minimal noise and excellent ZETA values. It minimally affects the flow.

The correct insertion depth is visible through the three integrated inspection windows in the stainless steel press sleeve. This provides additional safety during installation.

No, for the dimension 16 x 2.0 mm, the Multikontur coupling (TH + U) is compatible. So you can also use a U press jaw.

Yes, the coupling is fully suitable for drinking water and DVGW-certified. All components are low in lead or lead-free and comply with the UBA positive list.

The pipe end must be calibrated and deburred after cutting. Insert the pipe all the way into the fitting; the correct depth is recognized by the inspection windows of the stainless steel press sleeve.

The coupling is designed for a long-term durability of 50 years. Moreover, it is a high-quality product that is "Made in Germany".

Yes, for a quick and secure pipe connection you only need press fittings, aluminum composite pipe, pipe cutter, calibrator, and a suitable press tool. An illustrated installation guide is included with the photos.