1 Inch Water Hose, 25mm Suction and Discharge Hose 8m with Fittings

The 8-meter length is often sufficient to reach a pool edge and empty it, depending on the pump's placement. With a 1-inch diameter, a good flow is guaranteed for 5000 liters. (Roughly: 8m range allows a working area of approx. 200 m² around the pump location.)

The included brass hose fittings have a 1-inch internal thread. They therefore fit directly onto many standard pumps with a corresponding 1-inch external thread. An adapter is usually not necessary.

The suction and pressure hose is well suited for use in the garden thanks to its flexibility and can also be guided through narrower passages. It is robustly constructed to largely avoid kinking.

The hose is designed for demanding conditions in the construction industry and is very robust. It should withstand brief driving over, for example by cars or smaller construction vehicles. A protective device is recommended for regular or heavy driving over.

Yes, the hose is explicitly designed as a suction and pressure hose. You can use it flexibly for both functions, depending on the requirements of your pump or application.

The hose comes with brass hose fittings on both sides (2/3 inch with 1 inch internal thread). This allows easy connection to most common pumps with a suitable thread without additional adapters.

Yes, this 1-inch suction and pressure hose is ideal for such scenarios. With its robustness and stable screw connections, it is ideally suited for pumping out basements with a dirty water pump.

Yes, the brass hose fittings can be exchanged for other coupling systems if required. Pay attention to the thread compatibility (1 inch female thread) and the correct fastening with hose clamps.

The hose is designed for use in pools. The materials are robust enough to withstand chlorinated or slightly salty pool water. However, regular rinsing after use is still advisable.

The 8m hose with an inner diameter of 25 mm holds about 3.9 liters of water. The additional weight from the water filling is therefore around 4 kg. (roughly calculated: about 0.5 kg per meter of hose filling).

No, the stainless steel hose clamps and brass hose fittings are supplied as a set, but are not pre-assembled. However, the installation is easy and quick to perform.

We recommend emptying the hose completely and storing it dry after each season. This extends the life of the material and protects against possible frost damage, although the hose is robust.

Yes, the hose is equipped with hose fittings on both sides. This makes it easy to connect several hoses of the same type to extend the range.

The hose is characterized by its high flexibility, which makes it easy to lay around corners or obstacles. It retains its dimensional stability and functionality.

Yes, the hose is designed as a suction and pressure hose and is suitable for sucking up sludge and similar media in the pond or pool. Its robust construction can withstand this.

The hose is designed for demanding conditions and is listed in the "Winterproof Garden Irrigation" category. However, for a longer lifespan, we recommend storing it frost-free, especially if it contains water.

The 8-meter length allows for a good reach for pond cleaning, depending on the size of the pond and the position of the pump. The brass hose fittings and stainless steel hose clamps ensure a very firm and secure connection.

Yes, the hose is ideal for use in the construction industry and for dirty water due to its robustness and flexibility. It can withstand demanding conditions.

The inner diameter is 25 mm (1 inch), which allows a good flow. It is designed as a suction and pressure hose and can withstand high loads from strong pumps.

Yes, the hose is robust and flexible and can withstand demanding conditions, which makes it suitable for use in agriculture, such as with slurry. The stainless steel hose clamps ensure a secure hold.

The stainless steel hose clamps and brass components are designed for durability and corrosion resistance, so the set will last a summer outdoors. However, an occasional visual inspection of the connections, especially after the first use, is advisable.

The hose is made of plastic with a reinforcement spiral. This spiral is specifically designed to maintain the hose's shape and prevent collapse even under strong suction.

Yes, the hose is designed for a working pressure of 6 bar. This is sufficient for many applications in the pond and pool sector, agriculture, or irrigation technology.

The suction and pressure hose set is intended for use in the construction industry. The robust construction and included suction strainer make it suitable for applications with dirty water pumps.

The product description does not explicitly state frost resistance for the hose. The valve is temperature resistant up to 100°C, but we recommend not storing the hose permanently outside in frost.

Yes, the 9-meter length of the hose set provides flexible reach. The floating intake is specifically designed to always draw the cleanest water from the surface, regardless of the water level.

Yes, due to the robust, UV- and ozone-resistant material, the hose is also suitable for use with saltwater. This makes it ideal for pools and ponds.

Yes, the hose is very robust despite its flexibility. It has high abrasion resistance and is suitable for use as a drag hose.

The set is described as robust and abrasion-resistant, promising high durability even with frequent use. You can rely on a long lifespan, even when in contact with rougher surfaces like cobblestones.

The hose is designed for a working pressure of up to 6 bar. That is sufficient for most garden irrigation systems.