1 Inch Water Suction Hose Kit with Floating Strainer, 15m

Yes, the hose of the set is chemical-resistant. It is therefore suitable for use with various irrigation agents or chlorinated pool water.

The suction-pressure hose set is versatile, including for pumping water. The floating extraction is ideal for pumping clean surface water.

No, all necessary components for installation are included in the scope of delivery of the BONI-42224-15. The assembly is simple and requires no special tools.

Yes, the set is temperature resistant up to 100°C. It can therefore also be used without any problems for warm water up to 80°C.

The hose is made of robust PVC and is reinforced with a plastic spiral. This ensures high resistance to external influences.

The set is robust, but is not explicitly declared frost-resistant. To avoid material damage, you should store it indoors in freezing conditions.

The 15-meter hose length offers a watering radius of 15 meters from the pump location. For 400 m², the pump may need to be moved to reach all areas.

The 1 inch diameter of the hose enables a high flow rate. The actual flow rate depends heavily on the pump used and the head. With a typical garden pump, 3,000 to 5,000 liters per hour are often achievable, which corresponds to about 50-80 liters per minute.

Extending the suction hose can reduce the pump's suction power. In principle, it is possible to extend it with suitable 1-inch couplings and another suction hose. Pay attention to the maximum suction height of your pump.

The set has a standard diameter of 1 inch. It is compatible with most commercially available pumps and connections of this size.

Yes, the floating intake of the BONI-42224-15 sucks water directly from the surface. This minimizes the risk of contamination from sediments on the bottom.

The floating extraction is designed to float freely on the water surface and adapt flexibly. An additional fixation is usually not necessary and not intended.

Yes, the floating intake is robustly built and can remain permanently in the pond or pool. The material is resistant to water and common environmental influences, however, a regular check for deposits is recommended.

The floating extraction sucks water from the surface and is equipped with a filter screen. This effectively reduces the suction of larger suspended matter such as leaves or flowers to protect the pump.

The floating intake is designed to draw water from the surface. A minimum depth of approx. 30 cm is recommended to avoid sucking up bottom sludge.

It is recommended to empty the floating intake and the entire hose set before the onset of frost and store it in a dry place. Although the hose is robust, ice formation and low temperatures can affect its lifespan.

Yes, the hose is reinforced by its plastic spiral and can withstand pressures of up to 6 bar. It is therefore suitable for powerful pumps. (Roughly: 6 bar corresponds to a delivery head of about 60 meters of water column.)

Yes, the hose is temperature-resistant up to 100°C. It can therefore also be used for pumping out very hot liquids, such as from a boiler. Pay attention to suitable pumps that are also designed for such temperatures.

The set is designed as a suction and pressure hose and is primarily intended for use with external suction pumps. With submersible pumps, the hose usually serves as a pure pressure hose, and the floating extraction is not required in this case.

Yes, the PVC hose is chemical-resistant and is therefore also suitable for conveying various irrigation agents as well as slightly acidic or alkaline cleaning solutions. Rinse the hose thoroughly after chemical use.

The stainless steel hose clamps and brass components are designed for durability and corrosion resistance, so the set will last a summer outdoors. However, an occasional visual inspection of the connections, especially after the first use, is advisable.

The hose is made of plastic with a reinforcement spiral. This spiral is specifically designed to maintain the hose's shape and prevent collapse even under strong suction.

Yes, the hose is designed for a working pressure of 6 bar. This is sufficient for many applications in the pond and pool sector, agriculture, or irrigation technology.

The suction and pressure hose set is intended for use in the construction industry. The robust construction and included suction strainer make it suitable for applications with dirty water pumps.

The product description does not explicitly state frost resistance for the hose. The valve is temperature resistant up to 100°C, but we recommend not storing the hose permanently outside in frost.

Yes, the 9-meter length of the hose set provides flexible reach. The floating intake is specifically designed to always draw the cleanest water from the surface, regardless of the water level.

Yes, due to the robust, UV- and ozone-resistant material, the hose is also suitable for use with saltwater. This makes it ideal for pools and ponds.

Yes, the hose is very robust despite its flexibility. It has high abrasion resistance and is suitable for use as a drag hose.

The set is described as robust and abrasion-resistant, promising high durability even with frequent use. You can rely on a long lifespan, even when in contact with rougher surfaces like cobblestones.

The hose is designed for a working pressure of up to 6 bar. That is sufficient for most garden irrigation systems.