13mm Hose Connector 90 Degree Elbow Fitting

Yes, the hose connector made of POM is resistant to alkalis and saline solutions. You can therefore use it for pipes through which corresponding cleaning agents occasionally flow.

Yes, the Y-piece is designed for operating temperatures from -40°C to +80°C. It can also withstand freezing conditions.

Yes, the connector made of polyacetal copolymer (POM) is abrasion-resistant. It is well suited for this, even if it is dragged over rough surfaces such as paving stones.

The hose connector made of POM is unstable to oxidizing agents, which also includes chlorine. Therefore, it is not suitable for permanent contact with chlorinated pool water.

No, the POM material is not resistant to acids, oxidizing agents, phenols, glycerin and glycol. Use the connector exclusively for suitable media.

The hose connector is designed for a maximum permissible pressure of 10 bar. Please check the pressure of your garden pump to ensure compatibility.

The connector is suitable for operating temperatures down to -40°C and can therefore also remain outdoors in freezing conditions.

The hose connector is designed for operating temperatures of up to +80°C. Temperatures over 60°C in the greenhouse are therefore harmless for the BONI-42195-25 and it can be used permanently.

The BONI-42195-25 connector is characterized by its impact resistance and high strength. Therefore, the material should be able to withstand occasional stepping on it.

Yes, the 90-degree angle of the connector is ideal for laying hoses even in hard-to-reach areas or corners without kinking. This ensures a uniform water flow.

Yes, the connector is designed for a maximum permissible pressure of 10 bar. This is sufficient for most irrigation systems in the garden.

The light weight of the connector is advantageous for handling and minimizes the stress on the connected hoses, which facilitates installation.

The connector is designed for hoses with an inner diameter of 10.0 mm. Standard 1/2 inch garden hoses usually have a larger inner diameter and therefore do not fit.

The connector is designed exclusively for hoses with an inner diameter of 10.0 mm. Pay attention to exact measurements for a tight connection.

Yes, the connector made of POM is resistant to gasoline, diesel, oils and greases. It can therefore also be used for corresponding lines.

Yes, the 90° angle of the connector is specifically designed for connecting hoses even in hard-to-reach areas or tight corners.

Thanks to the impact resistance and high strength of the POM material, the connector is robust and can withstand occasional loads such as stepping on it.

The operating temperature of the connector is -40°C to +80°C in continuous operation. It can withstand temperatures up to +110°C for a short time (up to 1 hour). It is not designed for a constant 90°C.

The polyacetal copolymer (POM) of the connector is resistant to oils and greases. Therefore, it is suitable for oil lines that carry these materials.

Yes, the polyacetal copolymer (POM) of the connector offers high strength, impact resistance, and abrasion resistance. These properties make it robust against many everyday stresses in the garden.

The connector withstands temperatures from -40°C to +80°C permanently. Briefly, even up to +110°C is possible.

The resistance depends on the type of cleaning agent. The Y-piece is resistant to alkalis and neutral salt solutions, but not to acids or oxidizing agents.

The Y-piece is resistant to neutral salt solutions and has a wide temperature range. It is suitable for outdoor use.

No, no special tools are required for assembly. Press the connector firmly onto the hose ends to achieve a tight connection.

The BONI-42195-48 is not suitable for antifreeze. Many antifreezes contain glycol, which the POM material is unstable against.

Regular cleaning of the Y-piece is not essential for the seal. However, it is recommended to inspect the connector for wear, especially after contact with chemicals, to maintain longevity.

The connector can withstand operating temperatures up to +80°C. Briefly (up to 1 hour) up to +110°C is also permissible.

The Y-piece is approved for a maximum pressure of 10 bar. This is usually sufficient for common irrigation systems with small pumps.

Yes, the polyacetal copolymer offers high impact resistance and abrasion resistance. The Y-piece is designed for daily, robust use.

Yes, you can connect several of these Y-pieces in a row to build branched hose systems. Pay attention to the maximum permissible pressure of 10 bar in the entire system.